Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2 Instrukcja Użytkownika Strona 120
- Strona / 200
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
120 Chapter 4 Spanning Tree, MLT, and Port-Mirroring
212160-A
With the BPS 2000 with software version 1.2, you can configure multiple
spanning tree groups (STGs). (Multiple spanning tree groups are available only
when the Stack Operational Mode is set to Pure BPS 2000 Stack.) The CLI allows
you to configure spanning tree groups, to add or remove VLANs to the spanning
tree groups, and to configure the usual spanning tree parameters and FastLearn.
This section covers the following topics:
• “show spanning-tree command,” next
• “spanning-tree stp create command by STG” on page 123
• “spanning-tree stp delete command by STG” on page 124
• “spanning-tree stp enable command by STG” on page 124
• “spanning-tree stp disable command by STG” on page 125
• “spanning-tree command by STG” on page 126
• “default spanning-tree command by STG” on page 127
• “spanning-tree add-vlan command” on page 127
• “spanning-tree remove-vlan command” on page 128
• “spanning-tree command by port” on page 129
• “default spanning-tree command by port” on page 130
• “no spanning-tree command by port” on page 131
show spanning-tree command
The show spanning-tree command displays spanning tree configuration
information that is specific to either the spanning tree group or to the port. The
syntax for the
show spanning-tree command is:
show spanning-tree [stp <1-8>] {config|port}
The show spanning-tree command is in the privExec command mode,
Note: When you omit the spanning tree group parameter (stp <1-8>) in
the any of the spanning tree commands, the commands operate on the
default spanning tree group (spanning tree group 1).
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 1.2 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- Contents 5
- Chapter 5 10
- Chapter 6 10
- Appendix A 11
- 12 Contents 12
- About this guide 19
- Before you begin 19
- Text conventions 20
- Related publications 21
- How to get help 22
- Preface 23 23
- 24 Preface 24
- Chapter 1 25
- CLI Basics 25
- Stacking compatibility 26
- Chapter 1 CLI Basics 27 27
- CLI command modes 28
- Chapter 1 CLI Basics 29 29
- 30 Chapter 1 CLI Basics 30
- Port numbering 32
- IP notation 33
- Accessing the CLI 33
- 34 Chapter 1 CLI Basics 34
- Figure 2 BPS 2000 banner 34
- Setting the CLI password 36
- Getting help 37
- Basic navigation 37
- General navigation commands 38
- Keystroke navigation 39
- BPS2000#show stack-info 46
- BPS2000#show stack-oper-mode 50
- Chapter 1 CLI Basics 51 51
- 52 Chapter 1 CLI Basics 52
- Chapter 2 53
- General CLI commands 53
- Setting the terminal 54
- Configuration Filename: 59
- Setting Telnet access 64
- Setting boot parameters 69
- Setting TFTP parameters 72
- Upgrading images 75
- Displaying interfaces 76
- Setting SNMP parameters 77
- Setting the system event log 82
- Displaying port statistics 85
- Enabling or disabling a port 87
- Setting port speed 89
- Enabling Autopology 92
- Enabling flow control 93
- Enabling rate-limiting 96
- 212160-A 100
- Chapter 3 101
- Security 101
- Using MAC address security 106
- command is: 107
- Parameters 111
- Description 111
- Using EAPOL-based security 112
- Using RADIUS authentication 115
- 118 Chapter 3 Security 118
- Chapter 4 119
- Using MLT 132
- Using port-mirroring 135
- VLANs and IGMP 139
- 140 Chapter 5 VLANs and IGMP 140
- Parameters and 141
- Chapter 5 VLANs and IGMP 145 145
- Using IGMP snooping 153
- 156 Chapter 5 VLANs and IGMP 156
- Displaying QoS parameters 158
- IP Filter Sets 163
- Resetting 168
- Configuring COPS 168
- Configuring QoS actions 180
- Configuring QoS meters 181
- Gathering QoS statistics 183
- Configuring QoS policies 184
- Reordering packets 186
- Command List 187
- 188 Appendix A Command List 188
- Appendix A Command List 189 189
- 190 Appendix A Command List 190
- Appendix A Command List 191 191
- 192 Appendix A Command List 192
- Appendix A Command List 193 193
- 194 Appendix A Command List 194
Powiązane produkty i podręczniki dla Switche sieciowe Avaya Reference for the Business Policy Switch 2000 Command Line Interface Release 1.2
Switche sieciowe Avaya 2216T Instrukcja Użytkownika
(118 strony)
(118 strony)
(16 strony)© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.052 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji