Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services Instrukcja Użytkownika Strona 86
- Strona / 390
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring IP, ARP, RARP, RIP, and OSPF Services
3-26
308627-14.20 Rev 00
Disabling and Reenabling an IP Interface
When you configure an IP interface on a circuit, the interface is automatically
enabled. You can use the BCC or Site Manager to change the state of the IP
interface as required.
Using the BCC
To disable or reenable an IP interface, go to an IP interface prompt (for example,
box; eth 2/2; ip/2.2.2.2/255.255.0.0
) and enter:
state
<state>
state
is one of the following:
enabled
(default)
disabled
For example, the following command disables IP interface 2.2.2.2:
ip/2.2.2.2/255.255.0.0#
state disabled
ip/2.2.2.2/255.255.0.0#
Using Site Manager
To disable or reenable an IP interface, complete the following tasks:
Site Manager Procedure
You do this System responds
1. In the Configuration Manager window,
choose Protocols.
The Protocols menu opens.
2. Choose IP. The IP menu opens.
3. Choose Interfaces. The IP Interface List window opens.
4. Click on the interface that you want to edit. Site Manager displays the parameter
values for that interface in the IP Interface
List window.
5. Set the Enable parameter. Click on Help
or see the parameter description on page
A-4.
6. Click on Apply, and then click on Done. You return to the Configuration Manager
window.
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.20 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 33
- OSPF Neighbors 37
- Neighbor Adjacencies 37
- Designated Routers 38
- AS External Routes 38
- OSPF Areas 39
- OSPF Router Types 41
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 43
- Route Weights 44
- Figure 1-7. IP Routing Table 46
- IP Traffic Filters 50
- Chapter 2 51
- Starting IP Services 51
- Starting RIP 53
- Starting OSPF 54
- Starting Router Discovery 54
- Adding RIP to an IP Interface 57
- Starting RARP 59
- Chapter 3 61
- Setting the ICMP Error Limit 75
- Caution: 81
- Customizing an IP Interface 84
- Specifying a MAC Address 97
- IP0012A 99
- Using the BCC 100
- Using Site Manager 100
- Configuring an SMDS Address 102
- (continued) 103
- Deleting IP from an Interface 106
- Defining a Static Route 117
- (continued) 119
- Defining a Default Route 121
- Customizing Router Discovery 122
- Choosing a Broadcast Type 124
- Chapter 4 129
- Customizing ARP 130
- Customizing Global ARP 131
- Figure 4-1. Proxy ARP Example 137
- Customizing RARP 141
- Deleting RARP Globally 144
- Chapter 5 145
- Customizing RIP Services 145
- Setting the RIP Diameter 146
- Customizing a RIP Interface 147
- Selecting the RIP Version 148
- ) and enter: 149
- Specifying the Update Mode 153
- Sending Triggered Updates 155
- Receiving RIP Updates 158
- Listening for a Default Route 161
- Defining a RIP Accept Policy 170
- Chapter 6 185
- Customizing OSPF Services 185
- Supplying an OSPF Router ID 188
- Figure 6-1. OSPF ASE Routes 193
- Setting the Holddown Timer 198
- <value> 199
- <seconds> 199
- Configuring Message Logging 200
- Changing the Area ID 205
- Specifying the Interface Type 206
- Estimating the Transit Delay 210
- Setting the Hello Interval 212
- Setting the Dead Interval 214
- Specifying the Metric Cost 217
- Specifying the MTU Size 219
- Examples 223
- Configuring Areas 226
- Configuring Authentication 229
- Configuring a Summary Route 231
- Configuring a Stub Area 233
- Transit area 244
- Policies 257
- Appendix A 263
- Site Manager Parameters 263
- IP Parameters 264
- IP Interface Parameters 266
- IP Global Parameters 280
- Static Route Parameters 289
- Adjacent Host Parameters 292
- Router Discovery Parameters 295
- RARP Parameters 297
- OSPF Parameters 298
- OSPF Global Parameters 299
- OSPF Interface Parameters 303
- OSPF Area Parameters 311
- Area Range Parameters 315
- OSPF NSSA Range Parameters 318
- RIP Parameters 324
- Manager online Help 331
- RIP Accept Policy Parameters 335
- OSPF Accept Policy Parameters 337
- Appendix B 353
- RIP Import Filters 354
- RIP Export Filters 357
- OSPF Import Filters 360
- OSPF Export Filters 363
- Appendix C 367
- Route Weight Worksheet 367
- Appendix D 371
- IP/OSPF Configuration Example 371
- Manager and the BCC 374
Powiązane produkty i podręczniki dla Oprogramowanie Avaya Configuring IP, ARP, RARP, RIP, and OSPF Services
Oprogramowanie Avaya PeriReporter Business Communications Manager Release 6.0 Instrukcja Użytkownika
(133 strony)
(133 strony)
Oprogramowanie Avaya CS1000 Instrukcja Użytkownika
(180 strony)
(180 strony)
Oprogramowanie Avaya Digital Enchanced Cordless Telecommuncations SIP DECT Fundamentals Instrukcja Użytkownika
(254 strony)
(254 strony)
Oprogramowanie Avaya Connecting BayStack AN and ANH Platforms to a Network Instrukcja Użytkownika
(178 strony)
(178 strony)
Oprogramowanie Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Instrukcja Użytkownika
(148 strony)
(148 strony)
Oprogramowanie Avaya Configuring Traffic Filters and Protocol Prioritization Instrukcja Użytkownika
(162 strony)
(162 strony)
Oprogramowanie Avaya BCM 4.0 Instrukcja Użytkownika
(398 strony)
(398 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.046 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji