Avaya Configuring Frame Relay Services Instrukcja Użytkownika Strona 47
- Strona / 162
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Frame Relay Overview
117376-B Rev. 00 2-21
All traffic that goes to a traffic-shaped VC (VC1 or VC2) is queued as high,
normal, or low priority at the VC level, and then it travels, by priority order, to a
shaping queue within the driver. Normal VC traffic is queued as high, normal, or
low priority at the driver level. At the driver level:
• Interrupt priority traffic, DLCMI/LMI requests (the LMI box in F
igure 2-9),
has the highest priority. You cannot change this.
• Shaped priority traffic (the Shaping box in F
igure 2-9) has the second highest
priority.
• Normal VC traffic (not shaped) has lower priority than shaped traffic. You can
still prioritize normal VC traffic as high, normal, or low.
Queuing and prioritization only matter when the traffic rate exceeds the VC line
rate or the CIR. If the total of all traffic is below the CIR, the router just transmits
it.
You cannot prioritize between VCs on which you have enabled traffic shaping.
The router schedules traffic among them in a round-robin manner.
For information about configuring filters for protocol prioritization, see
Configuring Traffic Filters and Protocol Prioritization.
Traffic Shaping for SVCs
Traffic shaping for SVCs works according to the descriptions in the previous
topics, except that SVCs derive the committed burst, excess burst, and throughput
values from a combination of the traffic shaping parameters that you configure,
and values that the frame relay network imposes. The network values are called
link layer core (LL Core) values,
Requesting Quality of Service for SVCs
When you configure traffic shaping for an SVC, you have several alternatives to
achieve the QoS that will best serve your network:
• You can set the SVC Traffic Shaping Disable parameter to Enable without
providing values for the traffic shaping parameters. The SVCs you configure
in this way use LL Core values that the network provides.
• You can set the SVC Traffic Shaping Disable parameter to Enable, and
provide values for the LL Core traffic shaping parameters.
- Configuring 1
- Frame Relay Services 1
- Contents 5
- Incoming 6
- 117376-B Rev. 00 11
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 22
- Configuring an SVC 23
- Configuring IP Adjacent Hosts 24
- Configuring IPX Adjacent Hosts 25
- 1-6 117376-B Rev. 00 26
- Chapter 2 27
- Frame Relay Overview 27
- Introduction 28
- Permanent Virtual Circuits 29
- Switched Virtual Circuits 29
- PVC and SVC Comparison 30
- Frame Relay Packets 30
- 117376-B Rev. 00 2-5 31
- Management Protocols 32
- Frame Processing 34
- Frame Relay Service Records 34
- Frame Relay Access Modes 35
- Direct Access Mode 36
- Hybrid Access Mode 36
- 2-12 117376-B Rev. 00 38
- Source Routing 39
- RFC 1490 39
- Address Resolution for PVCs 39
- Address Resolution for SVCs 40
- Traffic Control 40
- Data Compression 41
- Data Encryption 42
- Protocol Prioritization 42
- Congestion Control 42
- Traffic Shaping 44
- Quality of Service 45
- 2-20 117376-B Rev. 00 46
- Traffic Shaping for SVCs 47
- 2-22 117376-B Rev. 00 48
- Traffic Shaping Considerations 49
- WCP and CIR Enforcement 50
- Oversubscribing the Interface 51
- 2-26 117376-B Rev. 00 52
- X.213 Priority for SVCs 53
- Inactivity Timing for SVCs 53
- 2-28 117376-B Rev. 00 54
- Multiline for PVCs 55
- 2-30 117376-B Rev. 00 56
- PVC Pass Through 57
- Frame Relay Dial Services 58
- 2-34 117376-B Rev. 00 60
- Chapter 3 61
- Customizing Frame Relay 61
- Selecting a Management Type 62
- Selecting a DLCI Address Type 63
- Selecting Address Length 64
- Monitoring the Connection 65
- 3-6 117376-B Rev. 00 66
- Customizing PVCs 67
- To delete service records: 68
- Enabling Multicast 70
- Configuring PVC Pass Through 72
- 3-14 117376-B Rev. 00 74
- To enable congestion control: 75
- 3-16 117376-B Rev. 00 76
- Enabling Compression for PVCs 77
- 3-18 117376-B Rev. 00 78
- Removing Multiline Services 79
- Customizing SVCs 80
- Adding SVCs 81
- 3-22 117376-B Rev. 00 82
- Disabling SVCs 83
- Disconnecting SVCs 84
- To edit LAPF parameters: 85
- To edit Signaling parameters: 86
- To set X.213 priority values: 88
- 3-30 117376-B Rev. 00 90
- To enable traffic shaping 91
- Enabling Compression for SVCs 92
- To disable compression: 93
- Deleting Frame Relay 95
- Appendix A 97
- A-2 117376-B Rev. 00 98
- 100
- Site Manager Parameters 101
- 102
- 102
- A-8 117376-B Rev. 00 104
- A-10 117376-B Rev. 00 106
- SVC LAPF Parameters 107
- A-12 117376-B Rev. 00 108
- 109
- 110
- A-16 117376-B Rev. 00 112
- SVC Signaling Parameters 113
- A-18 117376-B Rev. 00 114
- A-20 117376-B Rev. 00 116
- Parameters for PVCs 118
- A-24 117376-B Rev. 00 120
- PVC Service Record Parameters 122
- 123
- 123
- A-28 117376-B Rev. 00 124
- 125
- A-30 117376-B Rev. 00 126
- A-32 117376-B Rev. 00 128
- SVC Service Record Parameters 130
- 133
- 134
- SVC Options Parameters 136
- A-46 117376-B Rev. 00 142
- A-48 117376-B Rev. 00 144
- A-50 117376-B Rev. 00 146
- A-52 117376-B Rev. 00 148
- Appendix B 151
- B-2 117376-B Rev. 00 152
- Table B-1. RIP Parameters 152
- B-4 117376-B Rev. 00 154
- B-6 117376-B Rev. 00 156
Powiązane produkty i podręczniki dla Networking Avaya Configuring Frame Relay Services
Networking Avaya X.25 Instrukcja Użytkownika
(148 strony)
(148 strony)
Networking Avaya BCM1000 Instrukcja Instalacji
(90 strony)
(90 strony)
Networking Avaya BCM3.x Instrukcja Użytkownika
(28 strony)
(28 strony)
Networking Avaya V.34 Instrukcja Użytkownika
(34 strony)
(34 strony)
Networking Avaya 1D5 Uwaga
(40 strony)
(40 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.289 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji