Avaya Configuring IP, ARP, RIP, and OSPF Services Instrukcja Użytkownika Strona 164
- Strona / 374
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring IP, ARP, RARP, RIP, and OSPF Services
5-26
308627-14.00 Rev 00
For example, the following command sets the state to disabled for RIP accept
policy pol_1:
accept/pol_1/rip# state disabled
accept/pol_1/rip#
Table 5-1. BCC Definition Parameters for RIP Accept Policies
Parameter Values Function
state enabled (default)
disabled
Enables and disables the policy that you
created
action ignore (default)
accept
Specifies whether the protocol ignores a route
that matches the policy or forwards the route
to the routing table manager
preference 1 (default) to 16 Assigns a metric value (the higher the
number, the greater the preference) to a route
that the protocol forwards to the routing table
manager. If confronted with multiple routes to
the same destination, the routing table
manager may use this value to decide which
route to insert. Routes for all networks
(0.0.0.0/0.0.0.0) should have the lowest
preference, and routes for the most specific
networks (longest address and mask) should
have the highest preference.
precedence 0 (default) to any
integer
Assigns a metric value to this policy (a policy
with a higher value takes precedence over a
policy with a lower value). This value
determines the order of precedence for
policies that match the same route.
- Configuring IP, ARP, RARP 1
- RIP, and OSPF Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 308627-14.00 Rev 00 10
- Before You Begin 17
- Text Conventions 18
- Acronyms 19
- Related Publications 21
- How to Get Help 22
- Chapter 1 23
- IP Addresses 24
- Subnet Addressing 26
- Supernet Addressing 29
- Autonomous Systems 30
- Figure 1-4. ARP Example 32
- OSPF Neighbors 36
- Neighbor Adjacencies 36
- Designated Routers 37
- OSPF Areas 38
- OSPF Router Types 40
- AS External Routes 40
- OSPF Implementation Notes 41
- Router Discovery Protocol 42
- Route Preferences 42
- Route Weights 43
- Figure 1-7. IP Routing Table 45
- IP Traffic Filters 48
- Chapter 2 49
- Starting IP Services 49
- Starting RIP 51
- Starting OSPF 52
- Starting Router Discovery 52
- Adding RIP to an IP Interface 55
- Starting RARP 57
- Chapter 3 63
- Caution: 80
- Customizing an IP Interface 82
- IP0012A 97
- Configuring an SMDS Address 100
- (continued) 101
- Using the BCC 103
- Using Site Manager 104
- Deleting IP from an Interface 107
- Defining a Static Route 111
- 3.2.4.5/255.255.0.0: 113
- Choosing a Broadcast Type 118
- Chapter 4 123
- Customizing ARP 124
- Customizing Global ARP 125
- (continued) 129
- Figure 4-1. Proxy ARP Example 130
- Customizing RARP 134
- Deleting RARP Globally 137
- Chapter 5 139
- Customizing RIP Services 139
- Setting the RIP Diameter 140
- Customizing a RIP Interface 141
- Selecting the RIP Version 142
- Specifying the Update Mode 147
- Sending Triggered Updates 149
- Listening for a Default Route 155
- Defining a RIP Accept Policy 163
- Chapter 6 179
- Customizing OSPF Services 179
- Supplying an OSPF Router ID 182
- Figure 6-1. OSPF ASE Routes 187
- Setting the Holddown Timer 192
- Configuring Message Logging 193
- Configuring an Area ID 198
- Specifying the Interface Type 199
- Estimating the Transit Delay 202
- Setting the Hello Interval 205
- Setting the Dead Interval 207
- Specifying the Metric Cost 209
- Table 6-6. Cost Settings 210
- Specifying the MTU Size 212
- Defining an Area 218
- Configuring Authentication 221
- Configuring a Summary Route 222
- Configuring a Stub Area 224
- 0.0.0.1: 229
- Policies 247
- Appendix A 251
- Site Manager Parameters 251
- IP Parameters 252
- IP Interface Parameters 254
- IP Global Parameters 269
- Static Route Parameters 276
- Adjacent Host Parameters 280
- Router Discovery Parameters 283
- RARP Parameters 285
- OSPF Parameters 287
- OSPF Interface Parameters 292
- OSPF Area Parameters 301
- Area Range Parameters 305
- OSPF NSSA Range Parameters 308
- RIP Parameters 314
- Appendix B 321
- Routing Policy Parameters 321
- RIP Accept Policy Parameters 325
- OSPF Accept Policy Parameters 326
- Appendix C 343
- RIP Export Filters 347
- OSPF Import Filters 350
- OSPF Export Filters 351
- Appendix D 355
- Route Weight Worksheet 355
- Appendix E 359
- IP/OSPF Configuration Example 359
- 10.1.1.0 360
- 255.255.255.0 (RIP Only) 360
Powiązane produkty i podręczniki dla Networking Avaya Configuring IP, ARP, RIP, and OSPF Services
Networking Avaya BCM450 Instrukcja Użytkownika
(22 strony)
(22 strony)
Networking Avaya BSGX4e Podręcznik Użytkownika
(206 strony)
(206 strony)
Networking Avaya Integrated Management Release 3.0 Standard Management Instrukcja Użytkownika
(52 strony)
(52 strony)
Networking Avaya a WAN Adapter Module in a BayStack ARN Router (114204 Rev. A) Instrukcja Użytkownika
(34 strony)
(34 strony)
Networking Avaya Integrated Management Release 2.2 Network Management Console Podręcznik Użytkownika
(154 strony)
(154 strony)
Networking Avaya 0604DAX Uwaga
(20 strony)
(20 strony)
Networking Avaya R5.0: Przewodnik Konfiguracji
(20 strony)
(20 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji