Avaya Configuring Frame Relay Services Instrukcja Użytkownika Strona 22
- Strona / 240
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring Frame Relay Services
1-2
117376-C Rev. 00
Preparing a Configuration File
To prepare a configuration file:
1.
Create and save a configuration file that has at least one WAN interface.
2.
Retrieve the configuration file in local, remote, or dynamic mode.
For information on these procedures, see the Quick-Start Routers.
Starting Frame Relay
You can use either the BCC or Site Manager to start frame relay using default
values for all parameters. Frame relay will automatically find out about PVCs
from the frame relay switch, and will place the PVCs into the default service.
Using the BCC
To enable frame relay:
1.
Configure a physical interface on an available slot/connector.
To configure a physical interface on a slot and connector, navigate to the
top-level box prompt and enter:
<interface_type>
slot
<
slot_number>
module
<
module_number>
connector
<
connector_number>
<interface_type>
is the name of a link- or net-module on the router.
<slot_number>
is the number of the slot on which the link module is located.
<module_number>
is the number of the module on which the slot is located.
<connector_number>
is the number of a connector on the link module.
After you configure a physical interface, the BCC returns a prompt that
specifies your current working location. For example, the following command
configures a serial interface on slot 1, connector 2.
box# serial slot 1 connector 2
serial/1/2#
- Configuring 1
- Frame Relay Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117376-C Rev. 00 10
- About This Guide 15
- Conventions 16
- Acronyms 17
- Bay Networks Customer Service 18
- How to Get Help 19
- Chapter 1 21
- Starting Frame Relay 21
- Configuring PVCs and SVCs 26
- Configuring an SVC 27
- Chapter 2 31
- Frame Relay Overview 31
- Introduction to Frame Relay 32
- Permanent Virtual Circuits 33
- Switched Virtual Circuits 33
- PVC and SVC Comparison 34
- Frame Relay Packets 35
- . Note, however 36
- Management Protocols 37
- BYS0037A 38
- LAPF Operational States 39
- SVC Signaling 41
- Call Setup 42
- Message Processing 43
- Frame Relay Service Records 44
- Frame Relay Access Modes 45
- Direct Access Mode 46
- Hybrid Access Mode 46
- Source Routing 48
- RFC 1490 48
- Address Resolution for PVCs 48
- Address Resolution for SVCs 49
- Traffic Control 50
- Data Compression 51
- Data Encryption 51
- Protocol Prioritization 51
- Traffic Shaping 53
- Quality of Service 55
- Traffic Shaping for SVCs 57
- Incoming 59
- Outgoing 59
- CIR Configuration Guidelines 60
- WCP and CIR Enforcement 60
- Oversubscribing the Interface 62
- X.213 Priority for SVCs 64
- Inactivity Timing for SVCs 64
- Multiline for PVCs 65
- PVC Pass-Through 67
- Frame Relay Dial Services 68
- Caution: 71
- Selecting a Management Type 72
- Selecting a DLCI Address Type 74
- Selecting Address Length 74
- Monitoring the Connection 76
- Polling Interval 77
- Full Enquiry Interval 77
- Customizing PVCs 81
- To delete PVCs: 87
- To move PVCs: 87
- Enabling Multicast 88
- Configuring PVC Pass-Through 90
- <integer> 100
- Enabling Compression for PVCs 102
- Using the BCC 103
- Using Site Manager 103
- Customizing SVCs 105
- For example: 107
- To delete service records: 107
- Call Screening and Blocking 108
- Disabling SVCs 112
- Disconnecting Active SVCs 114
- Setup Timer 121
- <value> 126
- (continued) 128
- Congestion Control 129
- Congestion Timer 130
- Congestion Counter 130
- Congestion Method 131
- To enable congestion control 134
- To enable traffic shaping 139
- To disable compression: 141
- To set X.213 priority value 143
- Deleting Frame Relay 144
- Customizing Frame Relay 145
- Appendix A 147
- Site Manager Parameters 147
- Figure A-2 148
- SVC LAPF Parameters 157
- SVC Signaling Parameters 163
- Parameters for PVCs 168
- PVC Service Record Parameters 172
- SVC Service Record Parameters 180
- SVC Options Parameters 186
- WHERE DOES THIS PARAMETER GO? 200
- Appendix B 201
- Table B-1. RIP Parameters 202
- Appendix C 209
- Monitoring Frame Relay Using 209
- BCC show Commands 209
- Commands for Frame Relay 210
- <option> 212
- <dlci> 215
- <name> 215
- ] [-service 216
- <multiline_name> 223
- <name> 228
Powiązane produkty i podręczniki dla Networking Avaya Configuring Frame Relay Services
Networking Avaya BCM 2.5 Podręcznik Użytkownika
(50 strony)
(50 strony)
Networking Avaya Glossary of Media Processing Server Series Terminology (Software Release 2.1) Instrukcja Użytkownika
(124 strony)
(124 strony)
Networking Avaya BayRS Version 15.2.0.0 Uwaga
(68 strony)
(68 strony)
Networking Avaya Configuring Ethernet, FDDI, and Token Ring Services Instrukcja Użytkownika
(156 strony)
(156 strony)
Networking Avaya VoIP Monitoring Manager Release 3.0 Configuration Instrukcja Użytkownika
(44 strony)
(44 strony)
Networking Avaya BCM200/400 Instrukcja Instalacji
(386 strony)
(386 strony)
Networking Avaya X.25 Instrukcja Użytkownika
(198 strony)
(198 strony)
Networking Avaya BCM450 Przewodnik Konfiguracji
(11 strony)
(11 strony)
Networking Avaya X.25 Instrukcja Użytkownika
(50 strony)
(50 strony)
Networking Avaya Configuring Ethernet, FDDI, and Token Ring Services Instrukcja Użytkownika
(136 strony)
(136 strony)
Networking Avaya BayRS Version 15.1.0.0 Uwaga
(72 strony)
(72 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji