Avaya Connecting BayStack AN and ANH Platforms to a Network Instrukcja Użytkownika Strona 132
- Strona / 178
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Connecting BayStack AN and ANH Systems to a Network
A-4 114074 Rev. A
2. Make sure that you enter the proper command at the router console to
configure the AN/ANH’s initial IP interface.
Refer to “Configuring the Netboot Interface” in
Chapter 5 if you need
instructions.
3. Make sure that the AN/ANH’s synchronous port configured for
EZ-Install is cabled to the upstream router, or that the port configured
for Netboot (synchronous or Ethernet) is cabled properly.
Router Not Sending BOOTP Responses
If a router is receiving BOOTP request messages but failing to return BOOTP
responses, do the following:
1. Use Site Manager to make sure the BOOTP relay agent forwarding table
associated with the router shows an IP address that is configured on the
IP router.
2. Make sure that the input IP address is correct. If the Hops count is lower
than the router’s position in the path, increase it.
Refer to “
Creating the BOOTP Client Interface Table” in Chapter 4 if you
need instructions.
3. Use the Configuration Manager to make sure that BOOTP and IP are
enabled on the incoming and outgoing interfaces.
4. Make sure that the link modules and drivers are enabled. Refer to
Configuring Routers if you need instructions.
BOOTP Server Not Sending BOOTP Responses
If the BOOTP server is receiving BOOTP requests but failing to respond to them,
do the following:
1. Follow the instructions in the section “Displaying the BOOTP Server’s IP
Routes” later in this appendix.
2. Follow the instructions in the section “Debugging the BOOTP Server”
later in this appendix.
- Connecting BayStack 1
- AN and ANH Systems 1
- Bay Networks Software License 3
- Contents 5
- 114074 Rev. A vii 7
- 114074 Rev. A ix 9
- 114074 Rev. A 10
- 114074 Rev. A xi 11
- 114074 Rev. A xiii 13
- About This Guide 15
- Before You Begin 16
- Conventions 17
- Acronyms 18
- 114074 Rev. A xix 19
- 114074 Rev. A xxi 21
- Bay Networks Customer Service 22
- World Wide Web 23
- Customer Service FTP 23
- Support Source CD 24
- CompuServe 24
- InfoFACTS 25
- How to Get Help 25
- Chapter 1 27
- 1-2 114074 Rev. A 28
- ANH Models 29
- 1-4 114074 Rev. A 30
- Access Node Software 31
- Software Management Tools 32
- Router Software 32
- Boot Configuration Options 33
- 1-8 114074 Rev. A 34
- The Boot Process 36
- 114074 Rev. A 1-11 37
- CAN0001A 38
- 114074 Rev. A 1-13 39
- 114074 Rev. A 1-15 41
- Local Boot 42
- CAN0006A 43
- Chapter 2 45
- EZ-Install 46
- Booting the Router Routinely 47
- Directed Netboot 48
- Completing a Startup Option 49
- 114074 Rev. A 2-7 51
- 2-10 114074 Rev. A 54
- Chapter 3 55
- Setting Up a UNIX Boot Server 55
- Setting Up BOOTP Sockets 56
- Setting Up BOOTPD to Run 57
- 3-6 114074 Rev. A 60
- 3-8 114074 Rev. A 62
- Setting Up a TFTP Server 63
- The examples in 64
- 114074 Rev. A 3-11 65
- 3-12 114074 Rev. A 66
- What to Do Next 67
- Chapter 4 69
- Configuring Network Booting 69
- Creating Configuration Files 70
- Preparing an Image 71
- Configuring Network Booting 75
- 4-8 114074 Rev. A 76
- 2. Click on Add 76
- Click on OK 77
- (Figure 4-4) 77
- 79
- 80
- CAN0007A 82
- 114074 Rev. A 4-15 83
- 4-16 114074 Rev. A 84
- 114074 Rev. A 4-17 85
- 4-18 114074 Rev. A 86
- 1. Click on Client I/F 87
- Chapter 5 91
- Network Boot Client 91
- <TFTP host> 92
- (continued) 92
- <TFTP 93
- (continued) 93
- <interface> 94
- <next 94
- <interface> 95
- <IP address> 95
- <subnet mask> 95
- <next hop 95
- 114074 Rev. A 5-8 98
- Chapter 6 99
- 101
- 6-4 114074 Rev. A 102
- 114074 Rev. A 6-5 103
- 6-6 114074 Rev. A 104
- About the N11 DCM 105
- 6-8 114074 Rev. A 106
- Ethernet Statistics Group 107
- Host Group 107
- HostTopN Group 108
- Matrix Group 108
- Filter Group 108
- Packet Capture Group 108
- Enabling the DCM 109
- 111
- 112
- 112
- 113
- 113
- 114
- 114074 Rev. A 6-19 117
- 2. Click on OK 119
- RMON Implementation Notes 121
- RMON Interoperability Issues 121
- 6-24 114074 Rev. A 122
- 114074 Rev. A 6-25 123
- 6-26 114074 Rev. A 124
- 114074 Rev. A 6-27 125
- 6-28 114074 Rev. A 126
- 114074 Rev. A 6-29 127
- Appendix A 129
- Router Fails to Netboot 131
- 114074 Rev. A A-5 133
- <connector> 135
- 114074 Rev. A A-9 137
- Displaying Parameter Settings 138
- 114074 Rev. A A-11 139
- Debugging the BOOTP Server 140
- Table A-1. BOOTP Messages 141
- <IP_address> 143
- Upgrading the Software Image 145
- Restoring a Local File System 145
- Appendix B 147
- Global Information Worksheet 149
- Router Protocol Worksheets 151
- OSPF Worksheet 152
- Wide-Area Protocol Worksheets 154
- Frame Relay Worksheet 155
- PPP Standard Worksheet 156
- CAN0008A 160
- Appendix C 161
- Implementation Notes 161
- C-2 114074 Rev. A 162
- Network Configuration Options 163
- Configuring a Single ANH 164
- 114074 Rev. A C-5 165
- Configuring Multiple Hubs 166
- CAN0010A 167
- C-8 114074 Rev. A 168
- CAN0011A 169
- CAN0012A 170
- 114074 Rev. A Index-1 171
- 114074 Rev. A Index-3 173
- 114074 Rev. A Index-5 175
- 114074 Rev. A Index-7 177
Powiązane produkty i podręczniki dla Oprogramowanie Avaya Connecting BayStack AN and ANH Platforms to a Network
Oprogramowanie Avaya Configuring SNMP, RMON, BOOTP, DHCP, and RARP Services Instrukcja Użytkownika
(148 strony)
(148 strony)
Oprogramowanie Avaya Configuring Traffic Filters and Protocol Prioritization Instrukcja Użytkownika
(162 strony)
(162 strony)
Oprogramowanie Avaya BCM 4.0 Instrukcja Użytkownika
(398 strony)
(398 strony)
Oprogramowanie Avaya Business Communications Manager - Multimedia Contact Center Instrukcja Użytkownika
(38 strony)
(38 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.047 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji