Avaya Configuring Dial Services Instrukcja Użytkownika Strona 90
- Strona / 258
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Configuring Dial Services
4-12
Modem Interface Parameter Descriptions
Use the following descriptions as guidelines when you configure the modem
parameters.
Parameter: Retry Delay
Default: 3 seconds
Range: 0 to infinity
Function: Specifies the number of seconds the router waits between attempts to re-
establish the connection.
Instructions: Enter the number of seconds you want the router to wait between retry
attempts.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.8.1.1.10
Parameter: Redial Count
Default: 3
Range: 1 to 10 attempts
Function: Specifies the maximum number of times that the router can attempt to
connect to a dial-up line before it is disconnected.
Instructions: Select a number between 1 and 10, inclusive.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.8.1.1.16
Parameter: Ring Indicator
Default: Enable
Options: Enable | Disable
Function: Enables or disables Ring Indicator (RI).
Instructions: If the dial-on-demand line is configured to use Raise DTR, and you have a
Series 5 router running 7.60 software, set this parameter to Disable.
Hardware versions earlier than 7.60 do not support RI. Otherwise, leave
the default, Enable.
MIB Object ID: 1.3.6.1.4.1.18.3.5.9.8.1.1.28
- Configuring Dial Services 1
- Bay Networks Software License 3
- Contents 5
- About This Guide 19
- CompuServe 21
- InfoFACTS 22
- World Wide Web 22
- How to Get Help 23
- Conventions 23
- Acronyms 24
- Chapter 1 27
- Dial Services Overview 27
- Dial-on-Demand Service 29
- Demand Lines and Pools 30
- Activating Demand Circuits 32
- Dial Backup Service 34
- Backup Lines and Pools 36
- Activating the Backup Line 37
- Bandwidth-on-Demand Service 38
- Activating Secondary Lines 40
- Terminating Secondary Lines 40
- Chapter 2 43
- ISDN Overview 43
- ISDN Standards 44
- Primary Rate Interface 45
- The D Channel 45
- Figure 2-3. LAPD Frame 46
- ISDN Interfaces 47
- Reference Points 48
- Chapter 3 51
- Implementation Notes 51
- D Channel Support 52
- B Channel Support 52
- S/T Interfaces 53
- BRI Subaddresses 54
- Selective PRI Service 55
- Call Screening 56
- Rate Adaption 56
- Example 1 57
- Example 2 57
- Point-to-Point Protocol 58
- IP Adjacent Hosts 61
- Data Compression 62
- PPP Multilink 63
- Static Routes 64
- Protocol Prioritization 65
- Breath-of-Life Messages 67
- Bandwidth for Backup Circuits 68
- Chapter 4 79
- Using the MIB Object ID 80
- Configuring Line Pools 80
- Pool ID Parameter 86
- Line Media Type Parameters 86
- Adding Line Pools 87
- Configuring ISDN Lines 91
- PRI Physical Interfaces 93
- MCT1/MCE1 Clock Parameters 97
- MCT1/MCE1 Port Parameters 98
- MCT1 Port Parameters 100
- Creating Line Pools 101
- Configuring Dial Services 102
- MCE1 Port Parameters 105
- MCT1/MCE1 Logical Lines 108
- Logical Lines Parameter 111
- (continued) 113
- (continued) 114
- Configuring ISDN Logical Lines 116
- Logical Lines Parameters 118
- fills in the fields below it 121
- Local Phone Number Parameters 123
- Changing a Line Pool 127
- Changing Lines in a Pool 128
- Port Parameters 134
- Timeslots 134
- Chapter 5 137
- Configuring Circuits 137
- Interface for Dialup Lines 139
- Demand Circuit Parameters 140
- Configuring Circuits 141
- Click on Done 151
- Schedule Parameters 152
- Deleting Demand Circuits 155
- 4. Click on OK to save 157
- Providing Backup Circuits 164
- Click on OK 166
- Circuit Options Parameters 168
- Primary Circuit Parameters 169
- (Figure 5-19) 175
- (Figure 5-20) 176
- Manager window 176
- Deleting Backup Circuits 178
- Click on Done to exit 182
- Congestion Monitor Parameters 189
- (Figure 5-26) 194
- Chapter 6 197
- Configuring Phone Lists 197
- Configuring Phone Lists 199
- Chapter 7 209
- Caller Resolution Table 209
- (Figure 7-2) 210
- Appendix A 217
- Configuration Examples 217
- Dial-on-Demand Using PPP 218
- Demand Pools Configuration 219
- Demand Circuit Configuration 220
- Configuration Examples 221
- Configuration of Router 1 222
- Configuration of Router 2 223
- Demand Pool Configuration 224
- Outgoing Phone List 225
- Protocol Configuration 226
- Backup Circuit Configuration 230
- Backup Pool Configuration 235
- Type)➔Circuit Options window 236
- Appendix B 239
- Appendix C 247
Powiązane produkty i podręczniki dla Oprogramowanie Avaya Configuring Dial Services
Oprogramowanie Avaya Configuring and Troubleshooting Bay Dial VPN (DVS) Networks Instrukcja Użytkownika
(188 strony)
(188 strony)
Oprogramowanie Avaya CS1000 Instrukcja Użytkownika
(180 strony)
(180 strony)
Oprogramowanie Avaya Business Communications Manager - Personal Call Manager Podręcznik Użytkownika
(90 strony)
(90 strony)
Oprogramowanie Avaya v4.1 Instrukcja Użytkownika
(166 strony)
(166 strony)
Oprogramowanie Avaya VoIP Monitoring Manager Reference Release 3.1 Instrukcja Użytkownika
(114 strony)
(114 strony)
Oprogramowanie Avaya 4n(114973-A Uwaga
(60 strony)
(60 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.231 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji