Avaya Configuring WAN Line Services Instrukcja Użytkownika Strona 275
- Strona / 294
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Site Manager WAN Line Services Parameters
117345-B Rev. 00
A-67
Parameter: KG84A Sync Loss Interval
Path: COM Connector > Edit Line > Edit SYNC Parameters
Default: 50 cycles
Options: 2
|
5
|
10
|
25
|
50
|
100
|
200
|
500
Function: Specifies how many cycles the router should wait after detecting an FCS error.
If the router does not receive a valid frame within the specified number of
cycles, the router declares a loss of synchronization.
Instructions: Accept the default, 50 cycles, or select one of the valid options. Be sure to set
the RTS Enable parameter to Enable.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.68
Parameter: KG84A Remote Resync Wait
Path: COM Connector > Edit Line > Edit SYNC Parameters
Default: 200 cycles
Options: 2
|
5
|
10
|
25
|
50
|
100
|
200
|
500
Function: Specifies the number of cycles that the router waits for the remote KG84A
device to complete a resynchronization operation, when synchronization is lost
and a remotely initiated resynchronization has been detected. After this number
of cycles, the router software determines that the resynchronization has failed
and initiates another resynchronization.
Note that if you press the RESYNC button on the local KG84A device, the
router responds as if it were a remotely initiated resynchronization.
Instructions: Specify a different setting at each end of the point-to-point link to avoid a
possible race condition. Be sure to set the RTS Enable parameter to Enable.
MIB Object ID: 1.3.6.1.4.1.18.3.4.5.1.69
- Configuring 1
- WAN Line Services 1
- Trademarks 2
- Restricted Rights Legend 2
- Statement of Conditions 2
- Contents 5
- 117345-B Rev. 00 10
- About This Guide 19
- Before You Begin 20
- Conventions 20
- Acronyms 21
- Bay Networks Customer Service 24
- How to Get Help 24
- Chapter 1 27
- Getting Started 27
- To edit a circuit: 33
- Figure 1-4. Edit Lines Window 34
- Chapter 2 35
- Setting the BofL Timeout 41
- Setting the MTU 41
- Configuring Clocking Signals 43
- Setting the Signal Mode 45
- Setting Minimum Frame Spacing 49
- Setting the CRC Size 52
- Setting the Signaling Method 54
- Setting the Line Coding 55
- Configuring KG84A Security 55
- Setting the Retry Count 59
- Setting the Link Idle Timer 60
- Setting the Cable Type 61
- Setting the Retry Timer 61
- Setting a Priority 62
- Setting the Hold Down Time 63
- Setting the IFTF Pattern 65
- Chapter 3 77
- Asynchronous Services 77
- for information 78
- Setting the Remote IP Address 79
- Specifying the Remote Port 80
- Specifying the Local Port 80
- Setting the Idle Timer 81
- Chapter 4 83
- Setting the Option Mode 85
- Loopback Test Modes 89
- AN/ANH/ARN 90
- Chapter 5 93
- Enabling or Disabling BofL 96
- Using the BCC 100
- Using Site Manager 100
- Configuring HSSI Services 101
- Chapter 6 103
- Editing T1 Services 104
- Setting the T1 Frame Type 105
- Configuring WAN Line Services 106
- Figure 6-2. Bipolar Format 106
- Specifying Line Buildout 107
- Assigning Channel Functions 108
- Editing E1 Services 109
- Enabling or Disabling CRC 111
- Setting the Clock Source 111
- Chapter 7 113
- Setting the Clock Parameters 116
- Configuring a DS0A Connection 129
- Setting Parameters 131
- Table 7-2 132
- Defining Logical Lines 133
- (MCT1 Example) 134
- Circuit Name: MCE1_31_1 135
- Circuit name: MCE1_231_1 135
- (MCE1 Example) 136
- See the following sections: 137
- Caution: 139
- Assigning Timeslots 144
- About the Tests 149
- Setting Port Test Parameters 150
- Running Port Tests 153
- Running Logical Line Tests 158
- Send Command Function 159
- Chapter 8 161
- Configuring FT1 Services 161
- Configuring an FT1 Port 162
- Defining Logical Line 172
- Circuit name: 174
- Chapter 9 189
- Types of Multiline Circuits 190
- Multiline Example 191
- Software Considerations 192
- Logical Lines (MCE1 Example) 205
- Appendix A 209
- Asynchronous Line Parameters 210
- DSU/CSU Parameters 216
- E1 Line Parameters 218
- HSSI Line Parameters 221
- LAPB Parameters 226
- MCE1 Port Parameters 233
- MCT1 Port Parameters 237
- FT1 Port Parameters 252
- FT1 Logical Line Parameters 258
- Synchronous Line Parameters 263
- T1 Line Parameters 282
- Glossary 287
Powiązane produkty i podręczniki dla Networking Avaya Configuring WAN Line Services
Networking Avaya X.25 Instrukcja Użytkownika
(148 strony)
(148 strony)
Networking Avaya BCM1000 Instrukcja Instalacji
(90 strony)
(90 strony)
Networking Avaya BCM3.x Instrukcja Użytkownika
(28 strony)
(28 strony)
Networking Avaya V.34 Instrukcja Użytkownika
(34 strony)
(34 strony)
Networking Avaya 1D5 Uwaga
(40 strony)
(40 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji