Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika Pobierz pdf

Page 1

Configuring BayStack and Business Policy Switches

with the Preside Network Configuration System

This card summarizes how to get started using the Preside Network Configuration System (Preside NCS) to configure the

BayStack and Business Policy Switches (BPS) in your network. This document is intended for network engineers who have

some familiarity with Nortel Networks Layer 2 switches.

The Business Policy Switch 2000 requires version 1.2 software. The BayStack 350, 410, and 450 switches require versions

1.3–3.1 software.

Task list

The following summarizes an example of the configuration tasks you can complete using Preside NCS:

• “Configuring the switch IP address”

• “Importing or creating a switch configuration”

• “Adding stack units and media dependent adapters (MDAs)“

• “Configuring ports”

• “Configuring VLANs”

• “Configuring spanning tree groups (STGs)”

• “Configuring an Simple Network Management Protocol (SNMP) trap receiver”

• “Configuring an Extensible Authentication Protocol over LAN (EAP)”

• “Configuring media access control (MAC) security”

• Configuring QoS parameters:

— “Creating interface groups”

— “Accepting default mapping values”

— “Setting up filters“

— “Maintaining policing statistics“

— “Allowing or denying packet reordering“

— “Configuring actions“

— “Configuring meters“

— “Configuring policies”

— “Assigning mapping values”

If you are familiar with the BayStack Console Interface (CI), see the “Mapping Switch Console Interface commands to Preside NCS GUI

properties” table to locate the Preside NCS properties that you want to configure.

Each of the above tasks is explained in more detail in the procedures that follow.

Configuring the switch IP address

NOTE: If you have a properly configured BootP server in your network, it detects

the switch IP address automatically; you do not need to configure the IP address.

Connect a serial console and apply power to the switch. After the Nortel

Networks logo screen appears, press [Ctrl]-Y to access the Console

Interface (CI).

At the CI Main Menu, choose IP Configuration/Setup.

Type the in-band IP address or stack IP address, subnet mask, and default

gateway of the switch.

Press [Return] after each entry.

For a standalone switch, you enter the in-band IP

address. For a stack configuration, you enter the stack

IP address.

Click Task list to return to the list of tasks.

1 2 3 4 5 6 ... 10 11

Podsumowanie treści

Strona 1 - Task list

Page 1Configuring BayStack and Business Policy Switcheswith the Preside Network Configuration SystemThis card summarizes how to get started using the

Strona 2

Page 10Configuring policies1In the navigation pane, expand the switch and select QoS > Policy Table.2Click the Properties tab.3In the Index box, en

Strona 3 - Configuring VLANs

Strona 4

Page 2Importing or creating a switch configurationYou can import existing configurations to the Preside NCS database directly fromthe switch, or you c

Strona 5 - Protocol over LAN (EAP)

Page 3Configuring portsBy default, all unconfigured ports are untagged links in the default port-basedVLAN (VLAN 1), participate in normal learning ST

Strona 6

Page 4Configuring spanning tree groups (STGs)You can configure from one to eight spanning tree groups.1In the navigation pane, expand the switch and e

Strona 7 - Setting up filters

Page 5Configuring an Extensible Authentication Protocol over LAN (EAP)1In the navigation pane, expand the switch and select EAP.2In the Properties tab

Strona 8 - Setting up filter groups

Page 6Configuring the security table NOTE: You manually assign ports (Port 1...Port 24) to an entry (S1...S32). You enter the allowed source as an en

Strona 9 - Configuring meters

Page 7Creating interface groupsNOTE: Nortel Networks does not allow this action from NCS, because to complete the configuration, the switch must be r

Strona 10 - Assigning mapping values

Page 8Maintaining policing statisticsYou can configure the Business Policy Switch to maintain and display statistics on QoS policies. Statistics are o

Strona 11 - *312061-C*

Page 9Configuring actions1In the navigation pane, expand the switch and select QoS > Action table.2Click the Properties tab.3In the Index box, ente

Więcej dokumentów dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System

Aby wyświetlić dokument Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika

Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika (10 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika

Podsumowanie treści

Więcej dokumentów dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System