Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika Pobierz pdf

Page 1

Configuring BayStack and Business Policy Switches

with the Preside Network Configuration System

This card summarizes how to get started using the Preside Network Configuration System (Preside NCS) to configure the

BayStack and Business Policy Switches (BPS) in your network. This document is intended for network engineers who have

some familiarity with Nortel Networks Layer 2 switches.

The Business Policy Switch 2000 requires version 1.1 software. The BayStack 350, 410, and 450 switches require versions

1.3–3.1 software.

Task list

The following summarizes an example of the configuration tasks you can complete using Preside NCS:

• “Configuring the switch IP address”

• “Importing or creating a switch configuration”

• “Adding stack units and media dependent adapters (MDAs)“

• “Configuring ports”

• “Configuring VLANs”

• “Configuring a multilink trunk (MLT)”

• “Configuring an Simple Network Management Protocol (SNMP) trap receiver”

• “Configuring an Extensible Authentication Protocol over LAN (EAP)”

• “Configuring media access control (MAC) security”

• Configuring QoS parameters:

— “Creating interface groups”

— “Accepting default mapping values”

— “Setting up filters“

— “Configuring actions“

— “Configuring meters“

— “Configuring policies”

— “Assigning mapping values”

If you are familiar with the BayStack Console Interface (CI), see the “Mapping Switch Console Interface commands to Preside NCS GUI

properties” table to locate the Preside NCS properties that you want to configure.

Each of the above tasks is explained in more detail in the procedures that follow.

Configuring the switch IP address

NOTE: If you have a properly configured BootP

server in your network, it detects the switch IP

address automatically; you do not need to

configure the IP address.

Connect a serial console and apply power to the switch. After the Nortel

Networks logo screen appears, press [Ctrl]-Y to access the Console Interface

(CI).

At the CI Main Menu, choose IP Configuration/Setup.

Type the in-band IP address or stack IP address, subnet mask, and default

gateway of the switch.

Press [Return] after each entry.

For a standalone switch, you enter the in-band IP

address. For a stack configuration, you enter the

stack IP address.

1 2 3 4 5 6 7 8 9 10

Podsumowanie treści

Strona 1 - Task list

Page 1Configuring BayStack and Business Policy Switcheswith the Preside Network Configuration SystemThis card summarizes how to get started using the

Strona 2

Strona 3 - Configuring VLANs

Page 2Importing or creating a switch configurationYou can import existing configurations to thePreside NCS database directly from the switch, oryou ca

Strona 4 - Protocol over LAN (EAP)

Page 3Configuring portsBy default, all unconfigured ports are untaggedlinks in the default port-based VLAN (VLAN 1),participate in normal learning STP

Strona 5

Page 4Configuring a multilink trunk (MLT)You can configure from one through six multilinktrunk (MLT) groups.1In the navigation pane, expand the switch

Strona 6 - Setting up filters

Page 5Configuring media access control (MAC) security1In the navigation pane, expand the switch and select MAC Address Security.2In the Basic tab of t

Strona 7 - Setting up filter groups

Page 6Creating interface groupsNOTE: Nortel Networks does not allow this action from NCS, because to complete the configuration, the switch must be r

Strona 8 - Configuring policies

Page 7Setting up filter groups1In the navigation pane, expand the switch and select QoS > IP Classification.2Click the IP Table Filter tab.3In the

Strona 9 - Assigning mapping values

Page 8Configuring meters1In the navigation pane, expand the switch and select QoS > Meter Table.2Click the Properties tab.3Enter the properties val

Strona 10 - *312061-B*

Page 9Mapping Switch Console Interface commands to Preside NCS GUI propertiesIf you are familiar with the BayStack Console Interface (CI), use the fol

Więcej dokumentów dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System

Aby wyświetlić dokument Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika

Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika (11 strony)

Komentarze do niniejszej Instrukcji

Brak uwag

Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System Instrukcja Użytkownika

Podsumowanie treści

Więcej dokumentów dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Networking Avaya Configuring BayStack and Business Policy Switches with the Preside Network Configuration System