Avaya Business Policy Switch 2000 Command Line Interface Release 2.0 Instrukcja Użytkownika Strona 109
- Strona / 233
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Chapter 2 General CLI commands 107
Reference for the Business Policy Switch 2000 Command Line Interface
Table 49 describes the parameters and variables for the default duplex
command.
Enabling Autopology
You can enable the Optivity* Autopology* protocol using the CLI. Refer to the
www.nortelnetworks.com/documentation URL for information on Autopology.
(The product family for Optivity and Autotopology is Data and Internet.). This
section covers the following commands:
• “autotopology command,” next
• “no autotopology command” on page 108
• “default autotopology command” on page 108
Table 50 default duplex command parameters and variables
Parameters and
variables
Description
port <portlist> Specifies the port numbers to reset the duplex mode to factory
default values. Enter the port numbers you want to configure, or all
to configure all ports simultaneously. The default value is
autonegotiation.
Note: If you omit this parameter, the system uses the port number
you specified in the
interface command.
Note: You cannot enable autonegotiation on fiber optic ports. You
cannot disable autonegotiation on the BPS2000 1-GT and BPS2000
2-GT MDA ports.
- Reference for the 1
- Business Policy Switch 2000 1
- Command Line Interface 1
- Release 2.0 1
- Trademarks 2
- Restricted rights legend 2
- Statement of conditions 2
- USA requirements only 3
- European requirements only 3
- Taiwan requirements 4
- Canada requirements only 4
- Contents 7
- Chapter 3 11
- Chapter 4 11
- Chapter 5 12
- Chapter 6 13
- Appendix A 14
- About this guide 21
- Before you begin 21
- Text conventions 22
- Related publications 23
- How to get help 24
- Preface 25 25
- 26 Preface 26
- Chapter 1 27
- CLI Basics 27
- Stacking compatibility 28
- Chapter 1 CLI Basics 27 29
- New features 30
- CLI command modes 31
- 30 Chapter 1 CLI Basics 32
- Port numbering 34
- IP notation 36
- Accessing the CLI 37
- 36 Chapter 1 CLI Basics 38
- Figure 2 BPS 2000 banner 38
- Setting the CLI password 40
- Getting help 41
- Basic navigation 41
- General navigation commands 42
- Keystroke navigation 43
- Parameters 47
- BPS2000#show stack-info 51
- Chapter 1 CLI Basics 51 53
- BPS2000#show stack-oper-mode 56
- Chapter 1 CLI Basics 55 57
- 56 Chapter 1 CLI Basics 58
- Chapter 2 59
- General CLI commands 59
- Setting the terminal 60
- Configuration Filename: 65
- Setting Telnet access 73
- Setting boot parameters 77
- Setting TFTP parameters 81
- Upgrading software 84
- Observing LED indications 86
- Upgrading software images 87
- Displaying interfaces 90
- Setting SNMP parameters 92
- Setting the system event log 97
- Displaying port statistics 100
- Enabling or disabling a port 102
- Naming ports 104
- Setting port speed 105
- Enabling Autopology 109
- Enabling flow control 111
- Enabling rate-limiting 113
- Security 117
- Using MAC address security 122
- Index Mac Address 124
- _____ _________________ 124
- 1 00-60-AF-00-12-30 124
- command is: 125
- Using EAPOL-based security 130
- Using RADIUS authentication 133
- 134 Chapter 3 Security 136
- 212160-B 136
- Using MLT 150
- Using port-mirroring 153
- VLANs and IGMP 157
- 156 Chapter 5 VLANs and IGMP 158
- Parameters and 159
- Description 159
- Using IGMP snooping 172
- Displaying QoS parameters 176
- IP Filter Sets 181
- Resetting 187
- Configuring COPS 188
- Configuring QoS actions 206
- Configuring QoS meters 207
- Configuring QoS shapers 208
- Gathering QoS statistics 210
- Configuring QoS policies 211
- Reordering packets 213
- Command List 215
- 214 Appendix A Command List 216
- Appendix A Command List 215 217
- 216 Appendix A Command List 218
- Appendix A Command List 217 219
- 218 Appendix A Command List 220
- Appendix A Command List 219 221
- 220 Appendix A Command List 222
- Appendix A Command List 221 223
- 222 Appendix A Command List 224
- Appendix A Command List 223 225
- 224 Appendix A Command List 226
Powiązane produkty i podręczniki dla Switche sieciowe Avaya Business Policy Switch 2000 Command Line Interface Release 2.0
(13 strony)
Switche sieciowe Avaya 470/460/BPS Uwaga
(3 strony)
(3 strony)
Switche sieciowe Avaya BCM 2.5 Instrukcja Instalacji
(306 strony)
(306 strony)
Switche sieciowe Avaya Business Policy Switch 2000 Software Version 2.0 Instrukcja Użytkownika
(334 strony)
(334 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji